
code: SA-STL-ASFW
|
|
Camp Fixed Rope Clamp (With Cut Away Included)
|
|
|
|
|
|

code: SA-STL-ASRC
|
|
Camp Adjustable Axel Rope Clamp (With Cut Away Included)
|
|
|
|
|
|

code: FS-IS-RP203
|
|
ISC Mini Rope Grab
|
|
|
- Length 85mm
- Width 68mm
- Thickness 26mm
- Pin Bolted
- Material High Strength Aluminium
- Minimum breaking load Dependent on type & Dia of rope
- Approved standards EN 567, EN 353/2
- Finish ISC Red Anodised
- Quality 100% inspected
- Weight 174g
- Serial Numbered Yes
|
|
|

code: FS-IS-RP204
|
|
ISC Large Rope Grab for 13 - 16mm climbing rope (Bolted)
|
|
|
- Length 82mm
- Width 45mm
- Thickness 30mm
- Cheek Fixed
- Material Aluminium
- Minimum breaking load 22kn
- Approved standards EN 12275
- Finish ISC Red Anodised
- Quality 100% inspected
- Weight 95g
- Serial Numbered Yes
|
|
|

code: FS-IS-RP205
|
|
ISC Large Rope Grab for 13 - 16mm climbing rope (Quick Release Pin for Rigging Only)
|
|
|
- Length 82mm
- Width 45mm
- Thickness 30mm
- Cheek Fixed
- Material Aluminium
- Minimum breaking load 22kn
- Approved standards EN 12275
- Finish ISC Red Anodised
- Quality 100% inspected
- Weight 95g
- Serial Numbered Yes
|
|
|

code: FS-IS-RP500
|
|
ISC Rocker Rope Grab 10.5mm 12.7mm rope
|
|
|
- Length 122mm
- Width 65mm
- Thickness 22mm
- Cheek Swing
- Material Aluminium
- Minimum breaking load
- Approved standards EN 353/2 EN358
- Finish ISC Red Anodised
- Quality 100% inspected
- Weight 159g
- Serial Numbered Yes
|
|
|

 code: LY-71 20
|
|
Petzl ASAP Sorber 20cm
|
|
|
|
Description: Energy absorber with integrated lanyard for the ASAP. Designed to connect the ASAP mobile fall arrester to a harness. The energy generated from a fall is absorbed by the tearing of specific stitching.
Important notice: 3.9m of clearance is required above an obstacle / ground for this device to operate successfully when used with an ASAP.
Size: 20cm
Conformity: EN355
|
|
|

code: LY-B01
|
|
Petzl Tibloc Ascender
|
|
|
|
Very small and lightweight, it has many uses: rescues, hauling systems and rope climbing.
In high performance chrome steel.
Has a slot for evacuation of mud / ice etc on the rope.
Technical specifications :
Individually tested.
For use with single ropes from 8 to 11 mm ø.
Weight: 39 g
CE certified EN 567.
|
|
|

 code: LY-B02
|
|
Petzl Pantin Foot Ascender
|
|
|
Foot-mounted rope clamp
Used in conjunction with the CROLL and ASCENSION rope clamps.
Make ascending ropes quicker and less tiring.
Easy adjusts with DoubleBack buckle.
Under-foot strap is reinforced with Dyneema for abrasion resistance.
Can be removed from the rope with a simple backwards leg movement.
For single ropes between 8 and 13 mm in diameter.
Right foot only.
The PANTIN is not PPE.
EN Standard: Not PPE
|
|
|

 code: LY-B03
|
|
Petzl Shunt B03 Ascender
|
|
|
|
Petzl Shunt BO3
Conforming to EN567 standard, the Petzl Shunt BO3 is for use on single ropes from 10 to 11 mm.
The Petzl Shunt BO3 is a simple ascender that performs well in adverse conditions and is often used as a mechanical Prusik in systems and rappels.
|
|
|

code: LY-B16
|
|
Petzl Croll Ascender (GOLD)
|
|
|
|
Used together with the ASCENSION for ascending the rope.
Angled attachment hole and special shape allow it to remain flat against the stomach.
Rectangular upper hole for attachment of shoulder straps to position the CROLL correctly.
The CROLL slides up the rope easily as the user ascends.
Technical specifications :
Individually tested.
For use on single rope from 8 to 13 mm
Weight: 130 gCE certified EN 567.
|
|
|

code: LY-B17L
|
|
Petzl Ascension Left Handed
|
|
|
|
User-friendly handled rope clamp / grab :
|
|
|

code: LY-B17NN
|
|
Petzl Ascension Right Handed
|
|
|
|
User-friendly handled rope clamp / grab :
|
|
|

 code: LY-B18AAA
|
|
Petzl Basic B18AAA Ascender
|
|
|
|
Description: The Petzl Basic is a compact and lightweight rope clamp for use with ropes of diameters between 8 and 13mm
Features: Multi-purpose: ascending a rope, self-belaying on a fixed rope, as a progress capture device in hauling systems, etc. Trigger cam with teeth and cleaning slot: works even on dirty or icy ropes. Ergonomic spring-loaded catch is easy to use even when wearing gloves. Spring-loaded catch can be locked in the open position so the rope clamp can be put on or taken off the rope with one hand. Lower hole for connecting a lanyard. The upper holes allow a carabiner to be clipped so the rope clamp can be used for self-belaying or with hauling systems.
Size: For use with ropes of diameters between 8 and 13mm.
Conformity: EN567, UIAA
Breaking Load: Depends upon diameter and type of rope being used with the device. Please see manufacturers instructions for full loading figures
|
|
|

 code: LY-B19WAA
|
|
Petzl Ascentree B19WAA Ascender
|
|
|
|
Description: Double Hand Ascender for use with ropes of between 8 and 13mm in diameter. Designed for ascending double ropes in trees using the "footlock" technique or with two PANTIN foot ascenders.
Features: Ergonomic molded handle allows a comfortable yet powerful grip Cam is totally integrated into the body of the rope clamp to prevent rubbing Large handles can be used with thick gloves Lower holes for connecting a SPELEGYCA lanyard and installing a FOOTPRO foot loop with a quick link Upper holes through which a karabiner attaches the device to the rope (useful for back-up belays or hauling)
Colour: Silver
Size: For use with ropes of between 8 and 13mm in diameter.
Conformity: CE
Breaking Load: Depends upon diameter and type of rope being used with the device.
|
|
|

code: LY-B52
|
|
Petzl Macro Grab
|
|
|
|
Identical characteristics to the MICROGRAB. Intended for moving on fixed ropes (as a back-up belay), for hauling heavy loads, and as an anti-slip device in hauling systems.
Locking system which makes it necessary to thread one end of the rope through the device to avoid accidental separation from the rope.
Replaces a Prusik knot for improvising an adjustable lanyard.
Very compact and lightweight. Slides easily up the rope and jams when pulled down by the cam.
Slides easily downwards when pulled down if the cam is held in.
If overloaded or subjected to an impact force, the Macrograb may slip and act as a load limiter.
Technical specifications :
Individually tested.
For use on ropes from 12 to 19 mm.
Weight: 335 g
CE certified EN 567.
|
|
|

code: LY-B53
|
|
Petzl Micro Grab
|
|
|
|
Intended for moving on fixed ropes (as a back-up belay), for hauling heavy loads, and as an anti-slip device in hauling systems
Locking system which makes it necessary to thread one end of the rope through the device to avoid accidental separation from the rope.
Replaces a Prusik knot for improvising an adjustable lanyard.
Very compact and lightweight. Slides easily up the rope and jams when pulled down by the cam.
Slides easily downwards when pulled down if the cam is held in.
If overloaded or subjected to an impact force, the Macrograb may slip and act as a load limiter.
Technical specifications :
Individually tested.
For use on ropes from 9 TO 13mm.
Weight: 335 g
CE certified EN 567.
|
|
|

 code: LY-B54
|
|
Petzl Microcender B54 Rope Clamp With Removable Axle
|
|
|
|
Petzl MICROCENDER Rope clamp with removable axle Petzl MICROCENDER Rope clamp with removable axle
This multi-purpose ascender can be used on fixed ropes or in hauling systems. The pin design reduces the chance of accidental disconnection from the rope.
* Very compact and lightweight * Cam-loaded design provides superior holding force * Can be installed at any point on the rope * Pin, axle and cam are attached to device to help prevent loss
Technical specifications
Weight: 162 g CE / UIAA Aluminum body For use on single ropes 9-13mm
|
|
|

 code: LY-B71
|
|
Petzl Asap B71
|
|
|
|
Fall Arrest device (Must be used in conjunction with a compatible energy absorbing lanyard - L57 Absorbica, Absorbica Y and I or an ASAP'Sorber) used to stop a fall, slide or uncontrolled descent. This device locks even if the device is grabbed during a fall and works on both vertical or angled ropes. Unlike most other fall arrest devices, this one moves up and down the rope without manual intervention. For use on low stretch (semi-static) ropes of between 10.5 and 13mm. Comes complete with an OK Triact karabiner. Not for use on laid or twisted ropes.
Important notice: 4.5m of clearance is required above an obstacle / ground for this device to operate successfully when used with an Absorbica Y or I, 4.10m with a 40cm ASAP'Sober and 3.9m with an Absorbica L57 or a 20cm ASAP'Sorber.
Size: For use on low stretch (semi-static) ropes of between 10.5 and 13mm.
Conformity: EN353-2
Breaking Load: Please see manufacturers instructions.
|
|
|

code: LY-C47
|
|
Petzl Footpro
|
|
|
|
Designed for use with a handled rope clamp / grab for rope climbing.
DoubleBack buckle allows quick and simple adjustment.
Reinforcement for the foot resists abrasion and allows easy step-in.
Available complete with maillon rapide.
Technical specifications :
Weight: 135 g
|
|
|

 code: LY-L57
|
|
Petzl L57 Absorbica
|
|
|
|
Description: Energy absorber designed to be used with the ASAP for a fall arrest system. Designed to dissipate the energy developed in a fall of 4m maximum height and to limit the force on the user’s body to a maximum of 6 kN.
Note: The total length of the fall arrest system including the ABSORBICA must not be greater than 2 meters, as specified in the EN 354 and EN 355 standards. Requires a clearance height of at least 3.90 meters + the combined total length of the energy absorber, lanyard and connectors.
Size: Length 22cm. Length after tearing 160cm.
Conformity: EN355
|
|
|

 code: LY-L71 40
|
|
Petzl ASAP Sorber 40cm
|
|
|
|
Description: Energy absorber with integrated lanyard for the ASAP. Designed to connect the ASAP mobile fall arrester to a harness. The energy generated from a fall is absorbed by the tearing of specific stitching.
Important notice: 4.1m of clearance is required above an obstacle / ground for this device to operate successfully when used with an ASAP.
Size: 20cm
Conformity: EN355
|
|
|

 code: FS-GU-410
|
Stein Safety Cut-Away Strop This is from Lanyards/ Fliplines/ Throwbags
|
|
|
|
Cut-Away Strop 22kn rating for use with wire-core fliplines - also used for areial rescue
|
|
|

code: LY-P07
|
Petzl Mini Traxion Rope Clamp Pulley This is from Petzl/ISC Pulleys
|
|
|
|
MINI TRAXION - Multipurpose, lightweight and compact, swing-sided self-jamming pulley
A multipurpose 3 in 1 device (pulley, selfjamming pulley, rope clamp / grab) for hauling a sack, raising a person, setting up a hauling system or self-belaying.
- A compact device with a good coefficient of friction thanks to the sheave mounted on self-lubricating bushings.
- Efficiently replaces the traditional set-up: pulley (e.g. FIXE) + carabiner + rope clamp / grab.
- Equally ideal for movement on a tyrolean traverse or for rope climbing.
- Will find a place in all work or rescue kits.
Technical specifications :
- Working load in use as pulley only: 2.5 kN x 2 = 5 kN.
- Breaking load in use as pulley only: 10 kN x 2 = 20 kN.
- Working load in use as self-jamming pulley: 2.5 kN.
- Breaking load in use as self-jamming pulley: 4 kN.
- For use with ropes from 8 to 13 mm in diameter.
- Weight: 164 g
- Individually tested.
CE EN 567, EN 12278.
|
|
|

 code: LY-P51
|
Petzl Pro Traxion Rope Clamp Pulley This is from Petzl/ISC Pulleys
|
|
|
|
PRO TRAXION: Highly efficient self-jamming pulley. For efficient hauling of heavy loads: ideal for big wall climbing. Highly efficient large diameter sheave mounted on sealed ball bearings. Toothed cam with self-cleaning slot: works even on frozen or muddy ropes. Moving side piece permits the rope to be installed once the pulley is in place. Auxiliary attachment point for creating different types of hauling systems. Cam can be locked in open position so device can be used as a simple pulley. Certification: CE / UIAA. Technical specifications: Efficiency: 95 %. Working load as pulley only: 3 kN x 2 = 6 kN. Breaking strength as pulley only: 11 kN x 2 = 22 kN. Working load as self-jamming pulley: 2.5 kN. Breaking strength as self-jamming pulley: 4 kN. For use with ropes from 8 to 13 mm in diameter.
|
|
|